MIDITAPE

PRODUCT DESCRIPTION:

MIDITAPE (12mx12mmx0,10mm).(density: 0.35 g/ cm3). MIDITAPE thread seal tape  and is ideal for systems using water, drinking water and air. Max. pipe diameter: 1”. Temperature resistant from -200°C to +120°C. Max. pressure: 20 bar. MIDITAPE article no. 1000300

 

USE:

The types of tape described here are applied for the sealing of threaded joints on systems for water, drinking water, compressed air, cooling and steam systems and hydraulic systems. Applicable on all types of materials (iron, metal, plastic, fibre etc.). Thread seal tape is also suitable on systems where heavy hygiene requirements are made (hospitals, food industry etc.)

 

TECHNICAL PROPERTIES:

The exceptional strenght and high molecular weight of the carbon fibre-fluorine compound provides PTFE-tape series of outstanding qualities. Temperature proofed from -200°C to +260°C depending on tne density of the tape. On installations with a workintemperature higher than 90°C we recommed to use tape with a density of 1g/cm3 or more.PTFE-Tapes are resistant to almost all types of acids, bases, solvents, chemicals etc., however, with the exception of fluorine, some fluoride chemicals and melted alkali metals. Very low coefficient of friction. Non-inflammable (ASTM D-635 og D-470). Non-ageing. High tensile strenght even at low temperatures. Breaking-down resistant, especially, in connection with bending and vibrations. Sound electric insulating power independent of frequency and temperature.

 

DIRECTIONS FOR USE:

Remove any dirt and metal shavings from the thread before application of PFTE-tape. Put the tape on the thread joint in the direction of inclination of the thread. Apply the tape with an even, firm pull to be tight-fitting about the thread. Dependent on wanted thickness of layer the overlap should be from ½ to ¾ tape width. After assembling of the thread joints you should not disassemble. Dependent on pipe diameters the following type of tape is applied: Up to 25 mm UNITAPE is recommended. From 25 mm to 40 mm MAXITAPE is recommended. From 40 mm 65 mm JUMBOTAPE is recommended. Due to the fact that JUMBOTAPE is extremely flexible, it is ideal for coarse, damaged or sharp pipe threads. For very high pressure installations (e.g. hydraulic systems) thread seal seal tape with a high density is recommended anyhow (e.g. Maxitape). The tape is used alone and without any use of lubricants.

The information above is given on the basis of tests and experiences. However, since we have no knowledge about all details in the final use of the product we recommend a trial installation to ensure that the specification of the product matches the physical demands.

 

PACKAGING:

 

 

 

 

Item no.

Miditape

(250 pcs./box)

1000300

Related products

sealrite-gt12-gt19.jpg Sealrite GT12/GT19 Sealrite GT12/GT19 SEALRITE GT12/GT19 (5 m x 12/19 mm x 0.2 mm). HD. (density: 1.1 g/ cm3). High-End thread tape for systems where requirements for quality and safety have high priority. Very strong and economical in use. Available in 12 and 19 mm. Less suitable for fine thread. Temperature resistant from -200°C to +260°C.
SEALRITE 12 mm article no. 1000900
SEALRITE 19 mm article no. 1000950
Thread seal tapes from Unipak are white, non-adhesive thread seal tapes produced from pure Polytetraflourethylen (PTFE).
Klik for at læse mere
topseal.jpg Topseal Topseal TOPSEAL (12 m x 12 mm x 0.10 mm). HD. (density: 1.3 g/ cm3). Tested by BAM for liquid oxygen. Ideal for use in situations where there are high requirements for e.g. acid-resistance, pressure or heat. This product is very diffusion-proof and is therefore highly suitable for oil, petrol and diesel. APPROVED for gas and drinking water (EN 751-3 and DIN 30660). Otherwise same use as for other high-density tapes.
Klik for at læse mere
jumbotape.jpg Jumbotape Jumbotape JUMBOTAPE (15 m x 19 mm x 0.20 mm). MD. (density: 0.6 g/ cm3). Use as for UNITAPE. Very strong and flexible - ideal for large, coarse or sharp thread (rustproof). Ideal for steam. Economical in use. Pipe diameter: 3/4” - 2½”. Recommended temperature range from -200°C to +160°C. JUMBOTAPE article no. 1000500
Klik for at læse mere
multitape.jpg Multitape Multitape MULTITAPE (12 m x 12 mm x 0.10mm). HD. (density:1.0 g/ cm3). Use as for MAXITAPE. APPROVED for gas and drinking water (DG-2963). Ideal for hydraulics. Temperature resistant from -200°C to +260°C.
MULTITAPE article no. 1000600

Thread seal tapes from Unipak are white, non-adhesive thread seal tapes produced from pure Polytetraflourethylen (PTFE)
Klik for at læse mere
ptfetape.jpg P.T.F.E. Tape P.T.F.E. Tape Thread seal tapes from Unipak are white, non-adhesive thread seal tapes produced from pure Polytetraflourethylen (PTFE).
P.T.F.E Tape (10 m x 12 mm x 0.075 mm). LD (density: 0.2 g/ cm3). P.T.F.E. thread seal tape is ideal for systems with water, drinking water and compressed air. Max. pipe diameter: 3/4”. Temperature resistant from -200°C to +80°C. Max. pressure: 10 bar.
UNITAPE article no. 1000202


Klik for at læse mere
maxitape.jpg Maxitape Maxitape MAXITAPE (12 m x 12 mm x 0.10 mm) MD. (density: 0.7 g/ cm3). Use as for UNITAPE. Also ideal for steam. In addition, ideal for most chemicals, acids, bases, solvents, etc. Max. pipe diameter: 11/4”. Max. pressure: 30 bar. Also useful for hydraulics. Temperature resistant from -200°C to +180°C. MAXITAPE article no. 1000400
Klik for at læse mere
unitape.jpg Unitape Unitape UNITAPE (12 m x 12 mm x 0.075 mm). LD (density: 0.35 g/ cm3). UNITAPE thread seal tape is ideal for systems with drinking water and air. Max. pipe diameter: 3/4”. Temperature resistant from -200°C to +100°C. Max. pressure: 20 bar.
UNITAPE article no. 1000100
Klik for at læse mere

Need help? - Write to us